Synergy Lite 1 Year Sprayable Ceramic Coating

Basic Application: This application method is great if you are not machine polishing the vehicle and simply want the benefits of the ceramic coating with minimal effort. 

Thoroughly wash the vehicle, ensure any tar and contamination has been removed from the bodywork. The use of Liquid Fire is also advised to assist with chemical decontamination and if required you can also use a clay bar to assist in this process. 

Dry the vehicle after the wash process, this is essential! Always open doors and dry any areas like under wing mirrors where residual water can be lurking. A handy tool for this is the BLO Air-S car drier, but a dual twist towel like the mini will also do fine. 

Next, grab some Synergy prep to ensure any residual surfactants or light contamination from the chemical decon process is completely removed. This is essential to provide a completely clean surface for the coating to bond to. work on only 1 panel at a time or a half panel if you are working on a bonnet or roof. Spray prep and gently wipe in straight lines with a new microfibre towel, excess prep will just evaporate away. A good towel for this is our general weave 380gsm. 

Now to apply Synergy Lite, grab an applicator such as the microfibre ceramic application block. Spray the coating 6-8 times on the block to get the new pad surface primed then begin to apply the coating in straight lines 1 panel at a time. NEVER SPRAY DIRECTLY ON THE CAR. Ensure you crosshatch the coating on application by working it up and down then side to side as this will give a better, more even bond to the surface. Now simply allow 30 secs-5 mins ideally but can be left up to 15 mins before removing the coating residue with a short pile towel like the 280gsm edgeless, you may coat more than 1 panel at a time before removing. 

Once you have coated the entire car we recommend you give it a final wipe down with a plush edgeless towel like the 500gsm ultra plush. Once you have done this you are good to go! Just remember not to wash the vehicle for 7 days after application (very important). 

Advanced Application:

Advanced application is much the same as the basic, with the addition of machine correction on the vehicle to ensure optimum results in vehicle appearance and protection. Application and curing times remain the same on corrected paintwork. 

Layering can be done as many as 20 times with Synergy Lite, this may be desirable if you are trying to hide a deep imperfection that cannot be corrected by machine. To layer simply apply the first application then remove immediately, the second layer and so on should be left for 1-3 mins before removal. repeat this process until the defect has been completely filled. 

No idea what you're doing? 

Hold your horses there! We know you usually glance over these how-to sections while uttering "yeah, yeah, yeah, I know what I'm doing". We know we can trust you, but at the same time, we don't. 

Before you dive into coating your car for the first time, please familiarise yourself with the application guide above and if you need any help or advice you can contact us directly on 08000248625 via email on order@infinitywax.com or one of the best options our highly knowledgable and friendly Facebook group.

What is it?
Synergy Lite v2 is a true 1 year ceramic coating that can be applied outside and is extremely forgiving in nature, which makes it the perfect choice for DIY application or for mobile valeters & detailers. Its 100ml glass bottle contains enough product to cover 5 vehicles making it one of the best value ceramic coatings on the market. 

What's it made from?
Synergy Lite v2 is made from the same polysilazane resin as our professional coatings, just with lower ceramic content. This is combined with a trio of advanced solvents that allow the coating to be spread easily on your vehicle without the use of any oils. Finally, a polymer is added that bleeds through the ceramic and forms a top layer over the coating. This protects the vulnerable ceramic as it cures, and allows you to apply the coating to vehicles outdoors without causing failure. Lite is a true ceramic coating and when applied correctly and not washed for 7 days after application will reach 9H hardness just like the longer term coatings. 

What are the features?
Synergy Lite makes ceramic coating accessible to anyone, whether it's your first time applying a coating, or if you are an experienced installer. The problems associated with coating a car outside have been addressed with Lite and its sacrificial layer system. Think of this as a safety net that allows you to use a vehicle within 30 mins of application and even in the rain! In addition, we recognise that many DIY installers do not want to or cannot machine polish their vehicle, so we have designed lite to work even in these situations. The product has the ability to fill in surface defects such as wash marring and swirls quite dramatically and will leave your vehicle looking exceptional even without polishing.

How does it fit into the wash process? 
Synergy Lite is a last stage protection product and should only be applied after thoroughly washing, decontaminating, polishing (if required) and using Synergy Prep to prepare the panel. Ceramic coatings only work if they bond correctly to the paint so ensuring you prepare the vehicle correctly is very important.  

Why Has My Synergy Lite Trigger Stopped Working?
Synergy Lite contains ceramic coating technology that begins to cure when exposed to air and moisture. Small amounts of product can sometimes remain inside the trigger mechanism after use. If the product is stored between uses, this might affect spray performance or cause the trigger to become blocked. 

The good news is that the coating itself can still be perfectly fine. In most cases, simply replacing the trigger head will resolve the issue and allow you to continue using the product as normal.

What happens if it rains after applying Synergy Lite?

After applying Synergy Lite, we recommend allowing at least 30 minutes before the vehicle comes into contact with water, such as rain.

For the best results, we also recommend avoiding washing the vehicle or exposing it to cleaning chemicals for 7 days. This allows the coating to fully cure and achieve maximum durability and performance.

Unfortunately, the weather isn't something we can control. If it does rain after the initial 30-minute period, the coating should still provide protection. However, exposure to water during the curing period (within 30 minutes) may compromise the curing process slightly, which could reduce the overall longevity of the protection.